04:14 <scalepale> hey, is anyone around?

04:18 <scalepale> nevermind! I should read the error messages more carefully (I wanted to create a pyramid)

08:28 <_whitenotifier-3> [solvespace] Evil-Spirit commented on issue #440: Objects flip to the opposite side of constraints - https://git.io/fj23e

08:31 <_whitenotifier-3> [solvespace] Evil-Spirit commented on issue #426: Feature - New Group: Spiral (flat spiral) - https://git.io/fj23U

08:31 <_whitenotifier-3> [solvespace] Evil-Spirit edited a comment on issue #426: Feature - New Group: Spiral (flat spiral) - https://git.io/fj23U

10:41 <_whitenotifier-3> [solvespace] Symbian9 commented on issue #426: Feature - New Group: Spiral (flat spiral) - https://git.io/fj2Gy

10:58 <_whitenotifier-3> [solvespace] Evil-Spirit commented on issue #426: Feature - New Group: Spiral (flat spiral) - https://git.io/fj2Gj

10:59 <_whitenotifier-3> [solvespace] Evil-Spirit edited a comment on issue #426: Feature - New Group: Spiral (flat spiral) - https://git.io/fj2Gj

11:06 <_whitenotifier-3> [solvespace] Evil-Spirit commented on issue #426: Feature - New Group: Spiral (flat spiral) - https://git.io/fj2ZT

12:13 <jaggz> yyay

14:20 <jaggz> how can I constrain something in a range or limits? so something can rotate between angles 10 and 30 degrees...

15:03 <whitequark> jaggz: you can't (yet)

15:03 <whitequark> but you soon will be able to

15:09 <_whitenotifier-3> [solvespace] whitequark commented on issue #426: Feature - New Group: Spiral (flat spiral) - https://git.io/fj2ll

16:21 <jaggz> whitequark, thanks

16:21 <jaggz> (I did compile from the repo, btw)

16:22 <jaggz> I'm trying to figure out the appropriate measurements for the arms of a setup to change the angle of someone's bed

16:23 <jaggz> just one lifting-wheel is depicted here, but it'd be two https://www.youtube.com/watch?v=7E4iKWbLdwg&feature=youtu.be

16:52 <jaggz> whitequark, is there another way to go about this, without the limits on the constraints?

16:52 <jaggz> like, if I just set up some stuff kinda close to where I want it (like in that video)

16:55 <whitequark> sorry, I can't listen to audio in that clip and I didn't really understand it otherwise

17:03 <jaggz> whitequark, oh, no audio anyway. It's just a bed and I have a motor (linear actuator) -- trying to lift the bed to that angle with a rod that's fixed (hinged) to the bed and pulled so it rotates downwards.

17:03 <jaggz> the actuator is hinged to the underside of the bed and to some part of the swinging rod.

17:04 <jaggz> The rod will have a wheel on the end so that end can roll along the ground

17:04 <jaggz> (again, just one rod is depicted, but there will be two of them, following the same motion)

22:51 <sklv> hi, i have this part https://1g.gg/1.png with all the shown boxes ticked. I then make an assembly with that part https://1g.gg/2.png but I can't now select the points in the top face of 10mm_test_rect.slvs. any idea why?

22:59 <sklv> i managed to fix the problem by making the extrude double sided but i'd like to understand why it happened if pos