ajayr has quit [Remote host closed the connection]
ajayr has joined #imx6-dongle
newbie_GK802 has joined #imx6-dongle
<newbie_GK802>
hello guys, I got the GK802 and installed Debian into it. Thought that lm-sensors will work and I will be able to see the CPU temperature, but I just get "Sorry, no sensors were detected." message
hste has quit [Ping timeout: 245 seconds]
<newbie_GK802>
Is there some way to see what is the temperature of CPU from command line?
<newbie_GK802>
projectgus: I used your debian_installer to install the system to GK802, so now I apply to you: I have no experience in kernel building, but want some changes in kernel
<newbie_GK802>
I want to enable lxc on my device
<newbie_GK802>
and lxc requires namespaces and cgroup enabled
<newbie_GK802>
could you build the kernel with these options enabled?
<abrasive>
change into its dir and do "zcat /proc/config.gz > .config" to get the initial configuration from your running system
<abrasive>
then make menuconfig to change whatever it is you wanted to
<abrasive>
then 'make uImage', from memory, will generate you a uboot-formatted kernel image
<abrasive>
plenty of documentation out there if you get stuck. bbl
<newbie_GK802>
thanks, I'll give it a try
bsdfox\ has quit [Ping timeout: 245 seconds]
cnxsoft has quit [Ping timeout: 256 seconds]
bsdfox\ has joined #imx6-dongle
datagutt has joined #imx6-dongle
cnxsoft has joined #imx6-dongle
ajayr has quit [Ping timeout: 256 seconds]
<newbie_GK802>
drivers/video/mxc_hdmi.c: In function āmxc_hdmi_set_modeā:
<newbie_GK802>
drivers/video/mxc_hdmi.c:1650:2: warning: passing argument 1 of ādump_fb_videomodeā discards āconstā qualifier from pointer target type [enabled by default]
<newbie_GK802>
drivers/video/mxc_hdmi.c:198:13: note: expected āstruct fb_videomode *ā but argument is of type āconst struct fb_videomode *ā
<newbie_GK802>
drivers/video/mxc_hdmi.c: In function āmxc_hdmi_disp_initā:
<newbie_GK802>
drivers/video/mxc_hdmi.c:2241:3: warning: āreturnā with no value, in function returning non-void [-Wreturn-type]
<newbie_GK802>
is it safe to use such kernel? :)
ajayr has joined #imx6-dongle
<newbie_GK802>
or should I change something before continuing?
<abrasive>
nah, that's fine.
<newbie_GK802>
and now when I have the uImage, I place it to /boot/ directory and change the zImage link to the new uImage ?
<newbie_GK802>
or is it the zImage that is built, that I have to use?
eebrah is now known as eebrah|away
<abrasive>
er... if your u-boot is set up to boot from a zImage then you should make a new zImage
<abrasive>
not a uImage
<newbie_GK802>
"make uImage" created zImage also
<newbie_GK802>
so I guess I can use it
<abrasive>
yep.
cnxsoft has quit [Ping timeout: 264 seconds]
<newbie_GK802>
ok, then I try the reboot :)
<abrasive>
good luck :)
<newbie_GK802>
something went wrong, I can't connect to the device through ssh anymore :( and I'm at work now, so will have to wait for the evening :)
cnxsoft has joined #imx6-dongle
newbie_GK802 has quit [Quit: see you later]
ajayr has quit [Ping timeout: 245 seconds]
Noskcaj has quit [Ping timeout: 245 seconds]
cnxsoft has quit [Quit: cnxsoft]
eebrah|away is now known as eebrah
ajayr has joined #imx6-dongle
cnxsoft has joined #imx6-dongle
obinou has quit [Ping timeout: 245 seconds]
obinou has joined #imx6-dongle
cnxsoft has quit [Quit: cnxsoft]
hste has quit [Ping timeout: 245 seconds]
fossxplorer has joined #imx6-dongle
cnxsoft has joined #imx6-dongle
cnxsoft has quit [Remote host closed the connection]
alex_kag has quit [Ping timeout: 264 seconds]
hste has joined #imx6-dongle
rz2k has quit []
alex_kag has joined #imx6-dongle
alex_kag has quit [Quit: Konversation terminated!]
alex_kag has joined #imx6-dongle
alex_kag has quit [Ping timeout: 264 seconds]
alex_kag has joined #imx6-dongle
ajayr has quit [Ping timeout: 268 seconds]
ajayr has joined #imx6-dongle
Noskcaj has joined #imx6-dongle
datagutt has quit [Quit: Computer has gone to sleep.]