skullcrasher has joined #cubieboard
<skullcrasher> ok, got a working lubuntu server now
<skullcrasher> but still ethernet doesn't ...
<skullcrasher> i took the "official" server image from cubieboard site
smccarthy has quit [Remote host closed the connection]
<skullcrasher> how can i surely say that the ethernet part has a defect
fossxplorer has quit [Ping timeout: 265 seconds]
caveat- has joined #cubieboard
<skullcrasher> btw Turl, i could give u a dmesg|grep eth0 now :)
<Turl> a full dmesg would be even better
<skullcrasher> could take some minutes -.-
<skullcrasher> the only thing that worked before was wifi, but on server no iwconfig n stuff ...
<skullcrasher> omfg
<skullcrasher> guess if found it
<skullcrasher> if i press the cable into the port in a strange position it works ...
akaizen has quit [Read error: Connection reset by peer]
<skullcrasher> looks like the pins of the cable don't connect properly ...
akaizen has joined #cubieboard
<skullcrasher> but this can't be ...
<skullcrasher> 2 days old
Jachy has quit [Quit: Leaving.]
rz2k has joined #cubieboard
skullcrasher_ has joined #cubieboard
skullcrasher has quit [Read error: Connection reset by peer]
skullcrasher_ has quit [Quit: Leaving]
carlos-huang has joined #cubieboard
joedj has joined #cubieboard
t3st3r has joined #cubieboard
ghost75_ has joined #cubieboard
ghost75 has quit [Ping timeout: 240 seconds]
DV has quit [Ping timeout: 240 seconds]
bizarro_1 has quit [Quit: Leaving]
DV has joined #cubieboard
DV has quit [Ping timeout: 264 seconds]
rz2k has quit []
ricardocrudo has quit [Ping timeout: 252 seconds]
[7] has quit [Disconnected by services]
TheSeven has joined #cubieboard
akaizen has quit [Remote host closed the connection]
DV has joined #cubieboard
JohnDoe_71Rus has joined #cubieboard
laurent\ has quit [Ping timeout: 246 seconds]
laurent\ has joined #cubieboard
hramrach has quit [Remote host closed the connection]
sassmann has joined #cubieboard
akaizen has joined #cubieboard
focus has quit [Remote host closed the connection]
lauri has joined #cubieboard
<lauri> Hello
<lauri> I am having strange issues with HDMI on cubietruck
<lauri> Frist of all if I boot it without screen connected and plug in a screen later on, it is not picked up
<lauri> Occasionally the screen loses signal for a second or two
<lauri> With screen blanking I sometimes lose HDMI connection completely
DEac- has quit [Read error: Connection reset by peer]
DEac-_ has joined #cubieboard
akaizen has quit [Remote host closed the connection]
irc4001 has quit [Ping timeout: 255 seconds]
stefanro has quit [Quit: Leaving.]
stefanro has joined #cubieboard
fossxplorer has joined #cubieboard
fossxplorer has joined #cubieboard
focus has joined #cubieboard
retrosenator has joined #cubieboard
<retrosenator> does anyone know what the nc/12v plug on the cubie truck is for?
<lauri> retrosenator: I suppose it's for 12V rail of SATA disk
<lauri> retrosenator: if you use 3.5" desktop disks
<retrosenator> so I cannot power the cubie truck from 12 volts
stefanro has quit [Client Quit]
<retrosenator> there is already a 12v sata plug
stefanro has joined #cubieboard
<retrosenator> do you mean, the cubie truck needs an additional 12v to power the disk? It doesn't have an onboard booster?
<lauri> retrosenator: haha @ booster
stefanro has quit [Client Quit]
<lauri> retreosenator: I am pretty sure there is no onboard booster, that just would not make sense
<retrosenator> in any case my sata drive is 5v only it doesn't need 12v power but thanks
<retrosenator> I have to figure out how to power this thing from a 12 volt systen
<lauri> retrosenator: there is LiPo input
<lauri> retrosenator: but I don't know which voltage range it accepts
<retrosenator> what voltage should I use?
<retrosenator> I wonder if it boosts to 5 volts from 1 cell
<retrosenator> or drops to 5 volts from a 2 cell pack
<lauri> retrosenator: the "correct" way to power it is via barrel jacket 5V @ 2A
<lauri> retrosenator: (2A or more)
<retrosenator> I dont have a barrel jack unfortunately
<lauri> retrosenator: LiPo probably works with 2cell battery pack, but I haven't tried
<retrosenator> hmm, I have an adjustable buck converter from china
stefanro has joined #cubieboard
<retrosenator> 3 amp I believe
<retrosenator> so I guess I"ll set it to 5 volts
<retrosenator> just have to unsolder the barrel plug which is a bit of a pain
irc4001 has joined #cubieboard
<lauri> I just got these 2€ dual USB chargers from dealextreme
<lauri> 5V@2A
<lauri> seems to work quite well
<retrosenator> they take 11 to 15 volt input or so?
miner2015 has joined #cubieboard
<lauri> 220v -> 5v chargers
<retrosenator> oh, yeah that version is useless to me
<lauri> dealextreme also has these 12-36v -> 5v chips
<retrosenator> but they probably have a 12v one, doesn't matter
<retrosenator> I can't get things shipped here anyway
<lauri> to where? :D
<retrosenator> I'm in coron island
<JohnDoe_71Rus> we found that spends rtc battery and battery on a ct
<retrosenator> shipping is either $50, or it gets stolen
<retrosenator> anyway, I already have the 8-36 to adjustable 3 amp board so using that
irc4001 has quit [Ping timeout: 245 seconds]
MeGupsta has joined #cubieboard
abhinav2812 has joined #cubieboard
<MeGupsta> trying to get two wifi dongles on the cubieboard2, but only one of them gets registered as a wlan interface
<MeGupsta> wifi : edimax , driver used : 8192cu
<MeGupsta> can someone here please help me figure this out? thanks!
AdvancedNewbie has quit [Ping timeout: 240 seconds]
<rm> tried "ifconfig -a"?
<MeGupsta> yup, just no interface, doesn't even get registered at the 70.rules.persistent
<MeGupsta> which is weird, because when i tried to replace it with the tplink dongle, which uses a 8188eu driver, the driver gets loaded and i get a dmesg and lsusb out put and everything
<MeGupsta> just no wlan interface
<MeGupsta> i am wondering if this could be solved by adding something to the fex file but unsure of how to proceed with it
tat has quit [Remote host closed the connection]
<JohnDoe_71Rus> MeGupsta: you may need firmware for wifi
<MeGupsta> but i am able to run one dongle with success
<JohnDoe_71Rus> see system log
<MeGupsta> dmesg says something on the lines of not enough DMA
<MeGupsta> wait let me try and reproduce the exact error statement, sorry
<JohnDoe_71Rus> no.not. adapter in the system log can be determined. lacks the firmware to run. due to the legal restrictions on the firmware
<MeGupsta> hmm, which is weird because i was able to run both of them with the deprecated rtlwifi rtl8192cu drivers
<MeGupsta> its when i tried to replace the drivers with the new ones for running one of them as hostap, is when i encountered this problem for the first time
<MeGupsta> but i will try getting the firmware as well, apt-get realtek-firmware correct?
abhinav2812 has quit [Ping timeout: 245 seconds]
AdvancedNewbie has joined #cubieboard
popolon has joined #cubieboard
fossxplorer has quit [Remote host closed the connection]
fossxplorer has joined #cubieboard
tat has joined #cubieboard
<retrosenator> so now it's powered via the barrel connection
<retrosenator> and sata works, but no wifi or bluetooth
<retrosenator> it's using about .2 amps at 12 volts
wickwire has joined #cubieboard
Eyal_ has joined #cubieboard
nighty-_ has joined #cubieboard
iggy has quit [Quit: No Ping reply in 180 seconds.]
indy has quit [Remote host closed the connection]
iggy has joined #cubieboard
Midnightmyth has joined #cubieboard
<retrosenator> I got it working..
<retrosenator> going to try to use the cubie as an nfs server
<retrosenator> so I don't have to plug my usb harddrives in to use them
Jin|away is now known as Jin^eLD
<retrosenator> anyway, wifi is only transfering at 3mb/s over scp, hope nfs is faster
<JohnDoe_71Rus> retrosenator: For cb a10 was achieved 6.9 Mbit/s wget download and 4-5 Mbit/s WIFI connection. with https://romanrm.net/a10 this kernel
<retrosenator> I think I have a20
<rm> Mbit/sec or Mbyte/sec
<JohnDoe_71Rus> http://habrahabr.ru/post/215401/ if yoг know russian
<retrosenator> is the wget via ethernet?
<retrosenator> mine is mbyte/sec
<retrosenator> so about 24mbit/sec
<retrosenator> using builtin wifi on cubie truck
<retrosenator> I think ssh has a lot of overhead
<JohnDoe_71Rus> cubieboard not good for wifi router
<retrosenator> I want to use it to make a wireless harddrive
<retrosenator> I wonder if it can do wifi n
<retrosenator> also I can use it as a music player maybe
<rm> I have about 40 Mbit on both MK802 with a 5G WiFi dongle, and on Cubieboard A10 with a 2.4G one
<retrosenator> funny, iwconfig says not assiociated
<retrosenator> even though i am connected via ssh over wifi to see this
<retrosenator> it should be 54mbit minus overhead I think
<retrosenator> unless it can do wireless mode n
<retrosenator> what is p2p0?
kludge` has quit [Ping timeout: 255 seconds]
kludge` has joined #cubieboard
Jin^eLD has quit [Ping timeout: 245 seconds]
indy has joined #cubieboard
<retrosenator> I may make this thing into a server...
<retrosenator> is there a way to forward audio output from a laptop to the cubie over the network?
<retrosenator> maybe via bluetooth?
<rm> pulseaudio can do that
<rm> at least if your laptop also runs GNU/Linux
<retrosenator> oh cool.. how do I check the thermal sensors?
<retrosenator> everything is running linux on this boat
Ti_W_B has joined #cubieboard
<swabbles> retrosenator: pulseaudio.
<swabbles> rm: there are binaries for Microsoft Windows as well (never tried those though).
<rm> which install as a virtual audio card into the system?
<rm> or do you mean just as a sink (to playback stuff from other machines)
<swabbles> Within Linux it is just a sink.
<retrosenator> I just want to run an audio player on the laptop for example, and have it output to the speakers attached to the cubietruck
<swabbles> I am not sure how PA is supposed to work on Windows.
<retrosenator> trying to figure nfs out.. it's been a long time since I sued it
<swabbles> retrosenator: then you want to use PA.
<retrosenator> I'm going to go try to improve the junk rig on my kayak since the sun is down (not so hot) but I can still see
Ti_W_B has quit [Ping timeout: 265 seconds]
Jin^eLD has joined #cubieboard
<lauri> Okay DPMS is rather broken, once HDMI screen goes to sleep it never comes back :/
<rm> DPMS works fine for me in 24-bit colour modes
<rm> in 16-bit modes there is a screen corruption after wake-up
<lauri> swabbles: could you elaborate? I am on Debian Jessie, so I just need xf86-video-fbturbo driver and I should be good to go?
Jin^eLD has quit [Ping timeout: 255 seconds]
<swabbles> No, you have to configure xorg to not use dpms.
<swabbles> The xf86-video-fbturbo is what you should use for X11.
<lauri> with fbturbo the DPMS should work right?
<swabbles> No, DPMS doesn't work properly by default, which is why you want to use those xorg.conf settings.
<rm> it does work properly
<rm> with fbturbo, yes
<swabbles> rm: maybe as of recently, but the sunxi video driver is a mess.
<swabbles> And it isn't really related to sunxi, since I had to disable DPMS on my Chromebook as well.
<swabbles> So yes, if fbturbo has been patched to circumvent/solve that problem, then it will work.
<swabbles> Otherwise you'll have to disable it.
carlos-huang has quit [Quit: carlos-huang]
zn414 has joined #cubieboard
<retrosenator> ah, you have a chromebook and cubie truck too!
<swabbles> And a Cubieboard 2, IFC6410, olimex A10, and a Pandaboard ES :').
focus has quit [Remote host closed the connection]
retrosenator has quit [Ping timeout: 240 seconds]
<rm> I know it works now because it was a crucial feature for me
<rm> I even used an external USB DVI video "card" to have DPMS before that
Ti_W_B has joined #cubieboard
<swabbles> lol.
<swabbles> Will have to update it sometime then.
<lauri> swabbles: I installed fbturbo, it was detected by xorg aswell but still DPMS dies
<rm> ssh from a different machine and check what you have in dmesg and Xorg.log when it fails to wake up properly
<lauri> (that was 0.4.0 version though)
<rm> yeah ensure you use the latest version
<rm> if nothing helps, send the problem report to linux-sunxi mailing list
<lauri> alrighty
MeGupsta has quit [Quit: WeeChat 0.3.7]
retrosenator has joined #cubieboard
carlos-huang has joined #cubieboard
zn414 has quit [Ping timeout: 265 seconds]
bizarro_1 has joined #cubieboard
<retrosenator> I'm only getting 3mb/s over nfs :(
carlos-huang has quit [Quit: carlos-huang]
carlos-huang has joined #cubieboard
<retrosenator> I think it's maybe a cpu limitation actually because it's ntfs
deasy has joined #cubieboard
<rm> check if you have 100% CPU load
Ti_W_B has quit [Ping timeout: 252 seconds]
Ti_W_B has joined #cubieboard
zn414 has joined #cubieboard
<retrosenator> no, I tried on a normal directory
<retrosenator> still 3mb/s
deasy has quit [Quit: Nom d'un quark, c'est Edmonton !]
stefanro has quit [Quit: Leaving.]
stefanro has joined #cubieboard
<rm> over... wifi?
stefanro has quit [Client Quit]
<retrosenator> yes
<rm> and what is the wifi connection speed
<retrosenator> I don't know how to tell because iwconfig doesn't show this
stefanro has joined #cubieboard
<retrosenator> it says not associated even though it is working, and ifconfig output is normal
<rm> router doesn't show either? and what standard does the router support?
<retrosenator> it's not a router, its a chromebook
<retrosenator> running hostapd and udhcpd
<retrosenator> it supports abgn
<retrosenator> set to mode g
<retrosenator> I could try n I guess and see what happens but I dont think cubie truck can do that can it?
focus has joined #cubieboard
<retrosenator> anyway, at 54mbits I should get a lot more than 24mbits shouldn't I?
<lauri> nope
<lauri> 54mbit is theoretical limit
<lauri> in reality 54mbit card gets you about 20mbit
<lauri> that applies to ALL wifi cards
enrico_ has joined #cubieboard
<lauri> you get roughly half bandwidth of the advertised bitrate
<lauri> I managed to install fbturbo latest version
<lauri> but still dpms dies
<retrosenator> what is that?
<retrosenator> is it for framebuffer?
<lauri> fbturbo is supposed to give basic 2D acceleration
<lauri> and the guys said it would fix DPMS issues
<lauri> my monitor goes to sleep and it never wakes up
<rm> <lauri> in reality 54mbit card gets you about 20mbit <- yep correct
<rm> i have those 40 Mbit that I mentioned above on a connection that's displayed as 180 Mbit in iwconfig
<lauri> dmesg: iwconfig can show you whatever
<lauri> crap
<lauri> in dmesg nothing interesting is happening
stefanro has quit [Quit: Leaving.]
stefanro has joined #cubieboard
<lauri> [ 25.254] (==) FBTURBO(0): DPMS enabled
JohnDoe_71Rus has quit [Quit: Miranda IM! Smaller, Faster, Easier. http://miranda-im.org]
<retrosenator> rm: mode n?
<retrosenator> rm: does cubie truck support this speed?
impure_hate has quit [Quit: ZNC - http://znc.in]
<retrosenator> anyway that is lame, is there some way to have wifi raw mode without normal protocols or something for point to point ?
<lauri> ad-hoc exists but it's rather untested
<retrosenator> oh, I can use ad-hoc, is it any faster?
Jin^eLD has joined #cubieboard
ganbold_ has joined #cubieboard
rmarko has joined #cubieboard
rmarko is now known as impure_hate
<rm> <retrosenator> rm: mode n? <- yes, but I use external dongles on other A10 devices
<rm> <retrosenator> rm: does cubie truck support this speed? <- Cubietruck absolutely should support 11n, at least up to 150 Mbit
<rm> not sure about 300
<retrosenator> oh ok
<retrosenator> so maybe with ad-hoc and 150mbit I can get 60mbits heh
<lauri> you're supposed have two antennas for 300mbit
<retrosenator> how far apart do they need to be?
<lauri> retrosenator: I'd forget about ad-hoc
<lauri> retrosenator: don't you have AP?
<retrosenator> it isn't going to add speed is it?
<retrosenator> yeah I'm using the chromebook as the ap
zn414 has quit [Ping timeout: 265 seconds]
<retrosenator> I could make the cubie the ap if that would help
_massi_ has joined #cubieboard
<lauri> cubie works as AP
zn414 has joined #cubieboard
zn414 has joined #cubieboard
zn414 has quit [Changing host]
<lauri> with hostapd
<retrosenator> lauri: did you compare speed sto this vs ad-hoc?
<lauri> retrosenator: forget ad-hoc, if you're lucky it works with devices from same manufacturer..
<lauri> as I said it is not well tested mode
<lauri> for any device
DEac-_ has quit [Read error: Operation timed out]
<retrosenator> it has always worked fine for me in the past.. but ok
<retrosenator> what is a good vnc server to use for the cubietruck?
<rm> the regular one should work
ricardocrudo has joined #cubieboard
<rm> or actually no
<retrosenator> x11vnc?
<rm> you mean for sharing the existing GUI session?
<rm> for that yeah, x11vnc is available
<rm> but as a standalone VNC-only "Xorg", only "tightvncserver" is available
<retrosenator> I need hardware acclerated opengl
<rm> ...over VNC?
<retrosenator> mainly just for benchmark testing
<retrosenator> so the framerate over vnc is not important, only verifying the state it would have if I had a monitor
<retrosenator> hmm.. hostap unknown hw_mode 'n'
DEac- has joined #cubieboard
DEac- has quit [Ping timeout: 265 seconds]
<retrosenator> uh, it's going like 32mbits now
deasy has joined #cubieboard
<retrosenator> iw list is showing 54mbit as maximum though
zn414 has quit [Ping timeout: 265 seconds]
zn414 has joined #cubieboard
zn414 has joined #cubieboard
zn414 has quit [Changing host]
<retrosenator> weird.. if I run iwconfig from ssh to cubie I get a completely different result from running iwconfig from xterm in vnc
<retrosenator> also, the result from minicom (to the serial port) is the same as via ssh
<retrosenator> it's saying 65 Mb/s in the xterm in vnc
thesheff17 has quit [Read error: Operation timed out]
<lauri> it's not constant...
zn414 has quit [Read error: Connection reset by peer]
zn414 has joined #cubieboard
ninjak has joined #cubieboard
<lauri> okay fbturbo docs say that DPMS is broken and they suggest disabling it in xorg config
<lauri> but I think I noticed it should work with mali drivers
<rm> really do they?
<rm> where?
<retrosenator> so despite glxinfo giving direct rendering.. opengl is ridiculously slow.. do the mali drivers not work in x or something?
<retrosenator> not only slow but also buggy
swqa1549 has joined #cubieboard
zn414 has quit [Ping timeout: 268 seconds]
<ssvb_> retrosenator: mali400 drivers do not support opengl
zn414 has joined #cubieboard
<ssvb_> retrosenator: this is what you get instead - http://en.wikipedia.org/wiki/OpenGL_ES
<retrosenator> ok that is fine actually
<retrosenator> can I use opengles in x?
<ssvb_> yes
<retrosenator> because there are compatibility layers for opengles
<retrosenator> to give you big gl
<retrosenator> and it's actually just as fast.. they deprecated a lot of opengl for political reasons only
astrapotro has joined #cubieboard
<retrosenator> ok, will try mesa-demos for gles
swqa1549 has quit [Quit: swqa1549]
<retrosenator> I have libGLESv2.so but it's from october 2013..
swqa1549 has joined #cubieboard
stefanro has quit [Quit: Leaving.]
stefanro has joined #cubieboard
DEac- has joined #cubieboard
zn414 has quit [Ping timeout: 240 seconds]
zn414 has joined #cubieboard
zn414 has quit [Changing host]
zn414 has joined #cubieboard
swqa1549 has quit [Quit: swqa1549]
astrapotro has quit [Remote host closed the connection]
zn414 has quit [Quit: Leaving]
madmaxx has joined #cubieboard
t3st3r has quit [Remote host closed the connection]
t3st3r has joined #cubieboard
thesheff17 has joined #cubieboard
nils_2_ has joined #cubieboard
nils_2 has quit [Read error: Operation timed out]
retrosenator has quit [Ping timeout: 240 seconds]
nils_2_ is now known as nils_2
smccarthy has joined #cubieboard
kivutar has joined #cubieboard
stefanro has quit [Quit: Leaving.]
stefanro has joined #cubieboard
stefanro has quit [Quit: Leaving.]
stefanro has joined #cubieboard
kivutar has quit [Quit: Ex-Chat]
retrosenator has joined #cubieboard
Ti_W_B2 has joined #cubieboard
Ti_W_B has quit [Ping timeout: 264 seconds]
stefanro has quit [Quit: Leaving.]
stefanro has joined #cubieboard
Ti_W_B2 has quit [Ping timeout: 240 seconds]
stefanro has quit [Client Quit]
stefanro has joined #cubieboard
FR^2 has joined #cubieboard
thesheff17 has quit [Ping timeout: 252 seconds]
thesheff17 has joined #cubieboard
carlos-huang has quit [Quit: carlos-huang]
carlos-huang has joined #cubieboard
laurent\ has quit [Ping timeout: 255 seconds]
deasy has quit [Quit: Nom d'un quark, c'est Edmonton !]
ninjak has quit [Quit: Sto andando via]
toketin has joined #cubieboard
<retrosenator> anyone able to run the sunxi-mali test program?
akaizen has joined #cubieboard
FR^2 has quit [Quit: Connection reset by peer]
thesheff17 has quit [Ping timeout: 240 seconds]
akaizen has quit [Remote host closed the connection]
deasy has joined #cubieboard
Eyal_ has quit [Ping timeout: 265 seconds]
thesheff17 has joined #cubieboard
sassmann has quit [Ping timeout: 265 seconds]
franzolin[AWAY] has quit [Ping timeout: 255 seconds]
thesheff17 has quit [Ping timeout: 240 seconds]
toketin has quit [Quit: Konversation terminated!]
thesheff17 has joined #cubieboard
asie has joined #cubieboard
astrapotro has joined #cubieboard
DV has quit [Ping timeout: 240 seconds]
toketin has joined #cubieboard
_massi_ has quit [Remote host closed the connection]
carlos-huang has quit [Quit: carlos-huang]
DV has joined #cubieboard
Jin^eLD is now known as Jin|away
enrico_ has quit [Quit: Bye]
asie has quit [Quit: I'll probably come back in either 20 minutes or 8 hours.]
marco has joined #cubieboard
marco is now known as Guest11391
marco__ has joined #cubieboard
Guest11391 has quit [Read error: Connection reset by peer]
madmax has joined #cubieboard
madmax has quit [Excess Flood]
Gumboot_ has joined #cubieboard
toketin has quit [*.net *.split]
madmaxx has quit [*.net *.split]
Gumboot has quit [*.net *.split]
oatley_ has quit [*.net *.split]
old-papa has quit [*.net *.split]
old-papa has joined #cubieboard
oatley has joined #cubieboard
asie has joined #cubieboard
akaizen has joined #cubieboard
thesheff17 has quit [Ping timeout: 240 seconds]
thesheff17 has joined #cubieboard
syeekick has joined #cubieboard
<syeekick> hey
<syeekick> if i wanted to search google for something yet using cubieboard in the search term doesn't yeild results. Is there a product that is very very simlar in specification and the tutorials would work for said question?
akaizen has quit [Read error: Connection reset by peer]
akaizen has joined #cubieboard
hyperi0n has joined #cubieboard
<syeekick> is there any way you can brick the cubie truck?
marco__ has quit [Ping timeout: 268 seconds]
<rm> a product that is very very simlar in specification <- dunno, try "MK802"
<rm> but really
<rm> what is the question
<rm> if it's something rather generic, maybe even a Raspberry Pi tutorial will work
<rm> any way you can brick the cubie truck? <- not via software
marco__ has joined #cubieboard
rellla has quit [Ping timeout: 252 seconds]
rellla has joined #cubieboard
retrosenator has quit [Ping timeout: 240 seconds]
OutOfLine has joined #cubieboard
wickwire has quit [Remote host closed the connection]
marco__ has quit [Quit: Konversation terminated!]
retrosenator has joined #cubieboard
toketin has joined #cubieboard
uRandomMM has joined #cubieboard
tat has quit [Remote host closed the connection]
akaizen has quit [Remote host closed the connection]
sarwarc has quit [Ping timeout: 245 seconds]
akaizen has joined #cubieboard
laurent\ has joined #cubieboard
toketin has quit [Ping timeout: 240 seconds]
retrosenator has quit [Ping timeout: 240 seconds]
tat has joined #cubieboard
retrosenator has joined #cubieboard
toketin has joined #cubieboard
datagutt has quit [Ping timeout: 245 seconds]
toketin has quit [Quit: Konversation terminated!]
toketin has joined #cubieboard
<retrosenator> when I try to install xserver-xorg-video-sunximali it wants to remove about 50 packages!
tat has quit [Remote host closed the connection]
retrosenator has quit [Ping timeout: 240 seconds]
TheSeven has quit [Remote host closed the connection]
TheSeven has joined #cubieboard
smccarthy2 has joined #cubieboard
uRandomMM has quit [Ping timeout: 245 seconds]
hyperi0n has quit [Quit: :(){ :|:& };:]
smccarthy has quit [Ping timeout: 255 seconds]
asie has quit [Quit: I'll probably come back in either 20 minutes or 8 hours.]
smotocel69 has quit [Quit: Leaving]
emsyr has joined #cubieboard
madmaxx has joined #cubieboard
Guest29613 has joined #cubieboard
Baronawesome has joined #cubieboard
sarwarc has joined #cubieboard
thesheff17 has quit [Ping timeout: 240 seconds]
VargaD has quit [Quit: ZNC - http://znc.in]
VargaD has joined #cubieboard
astrapotro has left #cubieboard [#cubieboard]
lerc has quit [Ping timeout: 240 seconds]
smccarthy2 has quit [Remote host closed the connection]
smccarthy has joined #cubieboard
thesheff17 has joined #cubieboard
emsyr has quit [Quit: Konversation terminated!]
retrosenator has joined #cubieboard
<retrosenator> when I go to apt-get lxde, it removes xserver-xorg-video-sunximali
<retrosenator> and when I run xinit: (EE) module ABI major version (12) doesn't match the server's version (15)
OutOfLine has quit [Ping timeout: 240 seconds]
rundfunk has quit [Ping timeout: 252 seconds]
rundfunk has joined #cubieboard
toketin has quit [Read error: Connection reset by peer]
marco__ has joined #cubieboard
thesheff17 has quit [Ping timeout: 240 seconds]
Midnightmyth has quit [Ping timeout: 245 seconds]
<syeekick> thanks rm
<syeekick> would kali linux work on th cubieboard quite well? also how superior is the graphics chip on the cubieboard 2 compared to the cubieboard 3
akaizen has quit [Remote host closed the connection]
akaizen has joined #cubieboard
<retrosenator> which egl library do I use to link with the sunxi glesv2 library?
marco__ has quit [Quit: Konversation terminated!]
<retrosenator> gah, finally after editing the makefile and adding about 5 libraries
<retrosenator> I have a triangle
Jin|away is now known as Jin^eLD
setkeh has joined #cubieboard
<retrosenator> how do I get eglut for this?
lerc has joined #cubieboard
oatley has quit [Ping timeout: 240 seconds]
akaizen has quit [Read error: Connection reset by peer]
akaizen has joined #cubieboard
<retrosenator> the mesa eglut depends on the mesa egl too much to work
oatley has joined #cubieboard
Jin^eLD is now known as Jin|away
ganbold_ has quit [Remote host closed the connection]
AndrevS has quit [Ping timeout: 264 seconds]
<retrosenator> glmark2 fails to configure because egl and gles libraries are not installed as a proper package
AndrevS has joined #cubieboard
nighty-_ has quit [Quit: Disappears in a puff of smoke]
smccarthy has quit [Remote host closed the connection]