<karlp>
tuxd3v: because stmmac is the mac in allwinne parts... (turns out stmmac is a known historically bad name choice, but so be it, it's a designware IP iirc) micrel were mostly known for phys, not for macs iirc.
<karlp>
so this line, PHY [stmmac-0:01] driver [Micrel KSZ9031 Gigabit PHY] is just saying, that port 0:01 on the mac has a micrl ksz phy attached.
<karlp>
so... looks pretty aok to me :)
ChriChri_ has joined #linux-sunxi
<tuxd3v>
But for micrel shouldn't it be:
Mangy_Dog has quit [Ping timeout: 260 seconds]
<tuxd3v>
CONFIG_NET_VENDOR_MICREL=y
<tuxd3v>
CONFIG_NET_VENDOR_MICROCHIP=y
ChriChri has quit [Ping timeout: 258 seconds]
ChriChri_ is now known as ChriChri
<tuxd3v>
for what it seems it is the same shared driver because it was writen by STMicroelectronics perhaps..
<tuxd3v>
and some parts are re-used
popolon has quit [Quit: WeeChat 2.7]
lurchi_ has quit [Ping timeout: 260 seconds]
BenG83 has quit [Remote host closed the connection]
BenG83 has joined #linux-sunxi
lurchi_ has joined #linux-sunxi
victhor has quit [Ping timeout: 245 seconds]
<tuxd3v>
sun4i_ss seems to be fine now on Kernel 5.4.6 on A20 :)
<tuxd3v>
jernej, I don't have your network controller :(
<tuxd3v>
I built 5.4.6, and more or less all is ok
<tuxd3v>
have you included Micrel and Microchip drivers at kernel compilation?
lurchi_ is now known as lurchi__
AneoX has quit [Ping timeout: 260 seconds]
AneoX has joined #linux-sunxi
<smaeul>
btw ATF changes for H6 (AXP805) regulator setup were merged, so Ethernet on H6 in U-Boot now needs a U-Boot patch only
AneoX has quit [Ping timeout: 268 seconds]
AneoX has joined #linux-sunxi
cnxsoft has joined #linux-sunxi
TheSeven has quit [Ping timeout: 248 seconds]
TheSeven has joined #linux-sunxi
JohnDoe_71Rus has joined #linux-sunxi
<tuxd3v>
what is the sound driver codec for Alwinner a20 on linux kernel?
lurchi_ has joined #linux-sunxi
lurchi__ has quit [Ping timeout: 268 seconds]
lkcl has quit [Ping timeout: 260 seconds]
jonasbits has quit [Quit: No Ping reply in 180 seconds.]
jonasbits has joined #linux-sunxi
lkcl has joined #linux-sunxi
lkcl has quit [Ping timeout: 258 seconds]
dddddd has quit [Ping timeout: 265 seconds]
cnxsoft has quit [Ping timeout: 260 seconds]
<jernej>
tuxd3v: I don't have those set currently. I tried once with them, but they didn't help.
<jernej>
AFAIK NET_VENDOR options are for MAC drivers, not for PHY
NekoMay has left #linux-sunxi ["Leaving"]
<jernej>
anyway, I give up for time being, I have another A20 board which works just fine
<jernej>
smaeul: can you link U-Boot patch for U-boot H6 eth driver?
NekoMay has joined #linux-sunxi
<montjoie>
tuxd3v: sun4i_ss was not fine before ?
kaspter has joined #linux-sunxi
tllim has quit [Read error: Connection reset by peer]
return0e_ has joined #linux-sunxi
return0e has quit [Ping timeout: 268 seconds]
JohnDoe_71Rus has quit [Ping timeout: 268 seconds]
fl__0 is now known as fl_0
JohnDoe_71Rus has joined #linux-sunxi
suprothunderbolt has quit [Ping timeout: 260 seconds]
<tuxd3v>
montjoie, maybe sun4i_ss was ok, before.. I have never succeeded in configuring PRNG correctly... using RNG-tools .. and now out-of-the-box it just work with config CONFIG_CRYPTO_DEV_SUN4I_SS_PRNG=y
<tuxd3v>
maybe I missconfigured something , it could be..
<tuxd3v>
now at least on 5.4.6 its ok.
<tuxd3v>
jernej, I tested 5.4.6 and I have a complete oposite experience than yours..
<jernej>
which is?
gediz0x539 has quit [Quit: Leaving]
<tuxd3v>
stmmac doesn't know what is the phy attached, on my case but the driver works..
<tuxd3v>
ethernet works fine...well I haven't made (yet) badwith tests
<tuxd3v>
in Lime2
<jernej>
so maybe you're using generic phy driver
<tuxd3v>
I believe revision H of the board was wen they changed the phy to Microchip device..
<tuxd3v>
yes I suspect that I am
<jernej>
I have rev. K, which has Micrel PHY
<jernej>
which one do you have?
<tuxd3v>
I have the G revision..
<tuxd3v>
it should be Realtek, I beliebe
<tuxd3v>
but I was waiting for today, to shutdown and open the case, to check..
<tuxd3v>
but I really stranged since I have realtek drivers compiled too..
<jernej>
I think you should have CONFIG_REALTEK_PHY=y
<tuxd3v>
yeah I had it as a module..
<tuxd3v>
I put my builder to do another kernel..
<tuxd3v>
with config=y
<tuxd3v>
does any one experimented the userspace lima driver already?
<tuxd3v>
I built it some 1 month ago, but I will only try it now
JohnDoe4 has joined #linux-sunxi
JohnDoe_71Rus has quit [Ping timeout: 240 seconds]