nicdev has joined ##openfpga
m_w has joined ##openfpga
inoor has joined ##openfpga
Zarutian has quit [Quit: Zarutian]
_whitelogger has joined ##openfpga
inoor has quit [Read error: Connection reset by peer]
inoor has joined ##openfpga
_whitelogger has joined ##openfpga
m_w has quit [Quit: leaving]
inoor has quit [Ping timeout: 240 seconds]
inoor has joined ##openfpga
m_t has joined ##openfpga
pie_ has quit [Remote host closed the connection]
eric_j has joined ##openfpga
inoor has quit [Quit: inoor]
m_t has quit [Quit: Leaving]
Hootch has joined ##openfpga
theMagnumOrange has quit [Ping timeout: 240 seconds]
mifune has joined ##openfpga
mifune has joined ##openfpga
pie_ has joined ##openfpga
_whitelogger has joined ##openfpga
m_t has joined ##openfpga
jix has quit [Remote host closed the connection]
Hootch has quit [Read error: Connection reset by peer]
ZipCPU has quit [Ping timeout: 240 seconds]
mifune has quit [Ping timeout: 240 seconds]
mifune has joined ##openfpga
ZipCPU has joined ##openfpga
Hootch has joined ##openfpga
ZipCPU has quit [Quit: ZNC 1.6.4 - http://znc.in]
ZipCPU has joined ##openfpga
ZipCPU_ has joined ##openfpga
ZipCPU has quit [Quit: Leaving]
ZipCPU_ is now known as ZipCPU
m_t has quit [Quit: Leaving]
Zarutian has joined ##openfpga
scrts has quit [Ping timeout: 272 seconds]
scrts has joined ##openfpga
mifune has quit [Ping timeout: 260 seconds]
mifune has joined ##openfpga
mifune has joined ##openfpga
mifune has quit [Read error: Connection reset by peer]
mifune has joined ##openfpga
mifune has joined ##openfpga
digshadow has quit [Quit: Leaving.]
mifune has quit [Read error: Connection reset by peer]
mifune has joined ##openfpga
mifune has joined ##openfpga
m_t has joined ##openfpga
m_w has joined ##openfpga
mifune has quit [Ping timeout: 246 seconds]
Hootch has quit [Read error: Connection reset by peer]
mifune has joined ##openfpga
mifune has joined ##openfpga
mifune has quit [Read error: Connection reset by peer]
m_t has quit [Quit: Leaving]
pie_ has quit [Ping timeout: 260 seconds]
<azonenberg> So now that i have the starshipraider board set up
<azonenberg> i'm gonna try and repeat those pin to pin delay measurements i did on the greenpak
* azonenberg writes up a BSP file
<azonenberg> should have done this a while ago...
<m_w> azonenberg: what tools did you use for the PCB assembly?
<m_w> those boards look nice btw
kuldeep has quit [Excess Flood]
<azonenberg> my microscope for inspection and placement
<azonenberg> some old pcbs and masking tape as a jig for stencilling
<azonenberg> oshstencils credit card solder spreader
<azonenberg> some old nearly expired paste :p
<azonenberg> some fine-ish point tweezers for placing most components
<azonenberg> one of those suction pen thingies for placing the BGAs
<azonenberg> a pair of super fine tweezers for the 0201s
kuldeep has joined ##openfpga
<azonenberg> convection toaster oven for reflow
<m_w> must have some steady hands
<azonenberg> then a cheap aoyue iron for installin the PTH stuff
<azonenberg> I target-shoot and hand place WLCSPs
<azonenberg> 1mm bga is nothing by comparison
<azonenberg> Although the 0201 passives were a bit fun
<azonenberg> i'm kinda excited to try 01005s when my rework challenge board comes in
<azonenberg> i did them once a long while back
<azonenberg> but its been so long
<m_w> I did a few BGAs by hand recently and found I was a bit shaky
<m_w> just finished a few more beaglewire ice40 capes a few minutes ago: https://plus.google.com/+MichaelWelling79/posts/AqUXoYNNkGX
<m_w> I have a nice SMT pickup tool that I ordered for assembly
<m_w> well worth the $$$
<azonenberg> Tweezers are fine for me
<azonenberg> only thing i use the suction thing for is large bgas that my tweezers cant spread enough to grab
<azonenberg> and sometimes i just drop them on the approximate location by hand
<azonenberg> and nudge into place with tweezers
<azonenberg> trick is to get *good* tweezers
<m_w> yeah I use a SMT probe to adjust components after placing
<wpwrak> goot makes really nice ones: http://www.goot.jp/en/handakanrencat/pincette/